6GK1561-4AA02 西门子卡件

6GK1561-4AA02
 西门子连接PLC的6GK1561-4AA02通讯卡 西门子通讯卡 西门子卡件 西门子通讯网卡 西门子驱动主板  西门子PCI卡 西门子通讯模块 西门子通讯卡 
 
西门子代理商 接口网卡 profibus网卡 西门子通讯处理器   西门子工控通讯网卡 西门子工控通讯卡 西门子工控通讯主板
 西门子工控通讯模块

_______________________

【SIEMENS】

上海施承电气自动化有限公司

联     系       人：彭   立    道（销售工程师）

______________________________________

6GK1561-4AA01  

6GK1562-3AA00  
6GK1562-4AA00  
6GK1551-2AA00   
6GK1561-1AA01   
6GK1561-2AA00   
6GK1562-1AA00
6GK1562-1AM00
6GK1562-2AA00
6GK1571-1AA00
6GK1571-1AM00
6GK1561-3AA02
6GK1561-3AA01
6GK1162-8AA00
6GK1162-3AA00
6GK1161-3AA01 

PCI card (universal keyed 5 V/3.3 V) with own microprocessor for connection of PCs and SIMATIC PG/PC to PROFIBUS at up to 12 Mbit/s
Communication services:
PROFIBUS DP master and slave interface according to IEC 61158/61784 on one PCI card
PG/OP communication with STEP 5 and STEP 7
S7 communication with HARDNET-PB S7 software package
Open communication (SEND/RECEIVE) based on the FDL interface
Comprehensive diagnostics possibilities for installation, commissioning and operation of the module
High performance over direct dual-port RAM access
Event and filter mechanisms to reduce the loading on the host CPU
Multiprotocol operation and parallel operation of up to four CPs
Implementation of Motion Control applications is possible because a constant bus cycle time is supported
The appropriate OPC servers and configuration tools are included in the scope of supply of the respective communications software.

锚点

Benefits

Fast access to process data by means of direct access to the dual port RAM of the hardware
High computing performance in the PG/PC; 
reduces workload of host CPU by preprocessing the communication on the hardware
Use of different operating system environments; 
driver as source code for porting to different operating system environments
Reduced number of slots; 
through parallel operation as DP master and DP slave
Also used in motion control applications;
real-time capable data exchange through constant bus cycle time mode

锚点

Area of application

The CP 5614 A3 supports the connection of a SIMATIC PG/PC and PCs with PCI slot to PROFIBUS. It can be either a DP master or a DP slave.

Two different PROFIBUS networks can then be connected in a hierarchic structure on a PC with a PROFIBUS card and data can be transferred between the two.

The CP 5614 A3 provides high-performance support for control tasks on the PC (PC based Control, Numeric Control, Robot Control).

锚点

Design

Short PCI card
Operation possible in 3.3 V and 5 V PCI slots (universal keyed)
33 MHz or 66 MHz PCI clock
Operation possible as 32-bit card in a 64-bit PCI X-slot
2 x 9-pin sub-D socket for connection to PROFIBUS
Diagnostics LEDs
Parallel operation of up to four CPs
The module is installed by means of PCI standard mechanisms (Plug&Play).

If the CP 5614 A3 is used as DP master, DP slave, or in a PG/OP on a PROFIBUS DP, the connection is made:

to the electrical PROFIBUS via
Bus connector and PROFIBUS bus cable or
bus terminal (e.g. bus terminal 12M) and PROFIBUS bus cable
to the optical PROFIBUS with OLM via
bus cable with two bus connectors or
PROFIBUS plug-in cable 830-1T
to the optical PROFIBUS with OBT and integrated interface via
bus cable with two bus connectors or
PROFIBUS plug-in cable 830-1T

锚点

Functions

PROFIBUS DP

Access to process data

The CP 5614 A3 is operated as a PROFIBUS DP master and DP slave module that stores the process image (input/output and diagnostic data) in the dual-port RAM. High-performance data transfer to and from the PROFIBUS slaves is performed autonomously by the hardware of the CP 5614 A3. The user accesses the dual-port RAM directly.

The process data of the slaves is always consistent, i.e. the user receives the data of a slave from one and the same DP cycle.

Parallel operation of the HARDNET-PB DP software (DP master) and DP-Base software (DP master, DP slave) is not possible.

Example configuration of CP 5614 A3 as DP master and DP slave

Event filter mechanism

The user receives up-to-date data over two access mechanisms:

Cyclic polling of the DP slaves (high loading for host CPU)
Notification through event/filter mode on changing the input data of a slave (minimal loading for host CPU)
Both alternatives can be combined. This allows users to optimize use of the PC for their applications.

The event/filter mechanism can be used additionally for

Notification by means of an interrupt of the diagnostic alarms from slaves
During operation with constant bus cycle time, signaling by means of interrupt:
Start DP cycle
End cyclic data communication with DP slaves
FastLogic

FastLogic means that the CP 5614 A3 can react autonomously to 4 plant statuses. This results in a short response time and independence from the host application, e.g. fast shutdown of devices.

DP programming interface

The DP master programming interfaces of the CP 5613 A3 and CP 5614 A3 are identical.

The DP programming interface of the CP 5614 A3 features the following functions:

DP slave
DP master Class 1 including acyclic DP expansions
DP master Class 2 including acyclic DP expansions
The process data is accessed directly through the dual-port RAM. The DP RAM interface not only offers fast access as DP master/slave but also a basis for porting to other operating system environments (e.g. VXWorks, QNX, RMOS, RTX).

Administrative function calls (initialization and management services as well as diagnostic functions) are provided through a DP master and DP slave library (DP_BASE.DLL and DPS_BASE.DLL).

A transfer mechanism (PC application) can be activated in the software as a linking component for data transfer between the master and slave interface.

Defined I/O data can be transferred in this manner between the master interface and the slave interface.

The two connected PROFIBUS networks can be operated with different PROFIBUS bus parameters because they are independent of each other.

HARDNET-PB DP Development Kit

The HARDNET-PB DP Development Kit provides access to the functions DP master Class 1 and DP slave (incl. acyclic DP expansions)

The HARDNET-PB DP Development Kit is used to integrate the CP 5613 A3 and CP 5614 A3 communications processors into any operating system environment. The kit contains the necessary source code, including the descriptions in PDF format, and can be downloaded free of charge from the Internet.

Access to process data with HARDNET-PB DP

HARDNET-PB DP is available to permit compatibility with older applications that were created with the DP-Lib interface.

Parallel operation of the DP-Base and HARDNET-PB DP software is not possible.

Software for PG/OP communication

This software supports programming of the SIMATIC S7 controllers over PROFIBUS in combination with STEP 7. PG/OP communication is already available after the CP 5614 A3 (DP-Base) has been installed. No additional software packages are required.

Open communication (SEND/RECEIVE) based on the FDL interface

SEND/RECEIVE (FDL interface) is already available following installation of the CP 5614 A3 (DP-Base) and provides services for data transfer, diagnostics and management. No additional software packages are required.

Software for S7 communication (HARDNET-PB S7)

SIMATIC S7 system components communicate with each other using S7 communication functions. The S7 programming interface provides programming device/PC user programs with access to SIMATIC S7 system components. This provides easy, flexible access to the data of the SIMATIC S7 controller.

The following services are available with S7 communication:

Administrative services

Connection management
Mini database
Trace
Data transfer services

Read/write variables
BSEND/BRECEIVE (up to 64 KB per task)
User interfaces

OPC interface
The OPC server included in the respective software package can be used as the standard programming interface for the PROFIBUS DP (DP master and DP slave), open communication, S7 communication and PROFIBUS FMS protocols for linking automation technology applications to OPC-capable Windows applications (Office, HMI systems, etc.).

Configuration

The S7 communication, open communication, DP protocol (DP-V0/DP-V1/DP-V2) protocols are configured in STEP 7 or NCM PC.
A configuration tool is included in the scope of delivery of the PROFIBUS software packages.
Diagnostics

Comprehensive diagnostic tools are available (for installation, start-up and operation) for the module itself and for the PROFIBUS DP network. These tools can be used for quick and easy start-up of a PROFIBUS DP network with a CP 5614 A3.

Configuration example for CP 5614 A3

锚点

Technical Specifications

Order number

Product type designation

CP 5614 A3

Transmission rate

Transfer rate

● at the 1st interface acc. to PROFIBUS

9.6 kbit/s ... 12 Mbit/s

● at the 2nd interface acc. to PROFIBUS

9.6 kbit/s ... 12 Mbit/s

Interfaces

Number of electrical connections

● at the 1st interface acc. to PROFIBUS

1

● at the 2nd interface acc. to PROFIBUS

1

Type of electrical connection

● at the 1st interface acc. to PROFIBUS

9-pin Sub-D socket (RS 485)

● at the 2nd interface acc. to PROFIBUS

9-pin Sub-D socket (RS 485)

Supply voltage, current consumption, power loss

Type of voltage of the supply voltage

DC

Supply voltage

● 1 from backplane bus

3.3 V

● 2 from backplane bus

12 V

Relative symmetrical tolerance for DC

● at 3.3 V

9 %

● at 12 V

8 %

Consumed current

● 1 from backplane bus for DC maximum

0.15 A

● 2 from backplane bus for DC maximum

0.3 A

Active power loss

4 W

Permitted ambient conditions

Ambient temperature

● during operation

5 ... 55 °C

● during storage

-20 ... +60 °C

● during transport

-20 ... +60 °C

Relative humidity at 25 °C without condensation during operation maximum

85 %

Protection class IP

IP00

Design, dimensions and weight

Module format

PCI

Width

18 mm

Height

107 mm

Depth

125 mm

Net weight

118 g

Number of plug-in cards of same design plug-in per PC station

4

Number of units Note

-

Performance data

Performance data open communication

Software for open communication by means of SEND/RECEIVE required

FDL driver included in scope of delivery of the CP

Number of possible connections for open communication by means of SEND/RECEIVE maximum

80

Performance data PROFIBUS DP

Software for DP master function required

No

Service as DP master

● DPV0

Yes

● DPV1

Yes

● DPV2

Yes

Number of DP slaves on DP master usable

124

Amount of data

● of the address area of the inputs as DP master total

30 256 byte

● of the address area of the outputs as DP master total

30 256 byte

● of the address area of the inputs per DP slave

244 byte

● of the address area of the outputs per DP slave

244 byte

● of the address area of the diagnostic data per DP slave

244 byte

Software for DP slave function required

No

Service as DP slave

● DPV0

Yes

● DPV1

Yes

Amount of data

● of the address area of the inputs as DP slave total

244 byte

● of the address area of the outputs as DP slave total

244 byte

Performance data S7 communication

Software for S7 communication required

Yes, HARDNET-PB S7 (S7-5613)

Number of possible connections for S7/PG communication maximum

50

Performance data multi-protocol mode

Number of active connections with multi-protocol mode

50

Number of configurable connections per PC station

207

Product functions management, configuration

Configuration software required

Included in scope of supply

Product functions Diagnosis

Product function

● Port diagnostics

Yes

Standards, specifications, approvals

Standard

● for EMC

89/336/EEC

● for safety from CSA and UL

CAN/CSA C22.2 & UL 60950-1, UL 1950

● for emitted interference

EN 61000-6-3

● for interference immunity

EN 61000-6-2

Certificate of suitability

● CE marking

Yes

● C-Tick

Yes

锚点

More information

You can find the HARDNET-PB DP Development Kit on the Internet at:

http://www.siemens。。ｃｏｍ/simatic-net/dk5613

The CP 5614 A3 module can also be used under the LINUX and UNIX operating systems. Information on the available LINUX distributors and UNIX operating systems can be found at:

http://www.siemens。。ｃｏｍ/simatic-net/ik-info