DESCRIPTION
•Spindle auto speed shifting (3 steps) and CNC controlling.
•All casting are made of high tensile Meehanite cast iron which are annealed treatment to eliminate internal residual stress.
• Wide bed and box constructed, bed ways are high frequency heat treated, precision ground etc., to provide stability at high speed running or deep cut.
•Spindle & gear are made of CR-MO alloy steel which are carburizing & precisely ground, forced lubricating & oil bathed combined in headstock which can be prolonged servicing life.
•Three point support on the spindle with two taper roller bearings and one roller bearing to assure the accuracy & rigidity.
•High precision ball screw.
•CNC & Manual operation
•Tool radius & geometry compensation
•Constant surface speed for model with infinitive variable speed
•8 bit bus, 32K RAM
•Serial port (RS-232 communication)
•Teach-in mode
•Semiautomatic, automatic (Cycle) and part program modes
•Rapid travels
| Description/MODEL | Unit | AC-5160 | AC-5180 | AC-51120 | AC-51160 | AC-51200 | AC-51240 | ||||
| CAPACITY |
|
| |||||||||
| Center height | mm | 680 | |||||||||
| Swing over bed | mm | 1300 | |||||||||
| Swing over cross slide | mm | 900 | |||||||||
| Dist. between center | mm | 1700 | 2200 | 3200 | 4200 | 5200 | 6200 | ||||
| Width of bed |
| 770 | |||||||||
| SPINDLE |
|
| |||||||||
| Spindle bore | mm | Ø155(6") | Ø230(9")opt. | Ø305(12")(opt.) | Ø 410(16")(opt.) | Large spindle bores are available on request | |||||
| Spindle nose | - | A2-11 | A2-15 | A2-20 | A2-28 | ||||||
| Spindle speeds | rpm | H: 151~800 M: 31~150 L: 6~30 | H: 111~560 M: 21~110 L: 4~20 | H: 54~270 M: 11~53 L: 2~10 | H: 43~215 M: 9~42 L: 1.5~8 | ||||||
| TRAVEL |
|
| |||||||||
| Cross slide travel X-axis | mm | 680 | |||||||||
| Longitudinal travel Z-axis | mm | 1500 | 2000 | 3000 | 4000 | 5000 | 6000 | ||||
| Ball screw ( Dia. x pitch) | mm | X: Φ40 x P8 Z: Φ80 x P16 | |||||||||
| FEED RATE |
|
| |||||||||
| X-axis rapid travel | m/min | 5 | |||||||||
| Z-axis rapid travel | m/min | 6 | 5 | 4 | |||||||
| TAILSTOCK |
|
| |||||||||
| Quill dia. | mm | Ø165 | |||||||||
| Quill travel | mm | 300 | |||||||||
| Quill inside taper |
| MT#6 | |||||||||
| MOTOR |
|
| |||||||||
| Servo motor | kw | 22 / 33 、 28 / 42 (opt.) | |||||||||
| X-axis drive motor | Nm | 23.5 | |||||||||
| Z-axis drive motor | Nm | 32 | |||||||||
| Coolant pump motor | Bar | 6.2 (50HZ) / 8.3 (60HZ) | |||||||||
| WEIGHT |
|
| |||||||||
| Net weight | kg | 12000 | 12800 | 14400 | 16000 | 17600 | 19200 | ||||
Note:
We have the right tomodify the specification or designs. If there are subjected to change without
prior notice.
AC-5100 Series
ACCESSORIES
| STANDARD ACCESSORIES |
| OPTIONAL ACCESSORIES |
| l Fagor control | l Fanuc & Siemens Control on request | |
| l Main spindle 2 steps speed auto Change by | l 3-Jaw manual chuck | |
| l CNC Control | l 4-Jaw manual chuck | |
| l Coolant equipment | l 3-Jaw hydraulic chuck | |
| l Lubricate equipment | l Manual toolpost (4T) | |
| l Work light | l Electric servo toolpost (H4) | |
| l Center sleeve | l Electric turret (V8) | |
| l Dead center | l Hydraulic turret (V8) | |
| l Tool box & tools | l C axis (Living tool) | |
| l Operation & Service Manual | l Steady rest | |
|
| l Follow rest | |
|
| l Boring attachment | |
|
| l Double chuck system | |
|
| l Rotating center | |
|
| l Hydraulic tailstock | |
|
| l Rotating tailstock | |
|
| l Chip conveyer | |
|
| l Heat exchanger | |
|
| l Spindle oil cooler | |
|
|
| l Tailstock type : Build in type quill |
