功能描述
– Three driving rolls
三滚轮驱动
- Bending rolls with independent hydraulic adjustment for prebending of the leading and the trailing edge of profile
弯曲滚轮具有单独的液压控制系统，可以控制弯曲方向和侧翼辅轮的角度
- Two speeds for adjustment of bending rolls: fast approach at high speed and accurate final positioning at slow speed
弯曲滚轮无机变速控制，进给无机变速控制
- Lateral guide rolls with three-directional movement (axial, radial, angular) and mechanical adjustment, complete with anti-twisting cam roller for leg-in angle bending
侧面的导向轮可以在轴向、径向、角度三个方向运动同步运动，包括两侧导向辊完成的角度弯曲
- Position of rolls referenced with linear encoders 0.1mm accurate
位置控制采用线性编码器，精度0.1mm
- Controls actuated via remote free-standing console
能实现远程控制调整
- Horizontal-vertical working position combination
水平和垂直同步运动
CONSTRUCTION SPECIFICATIONS
结构描述
§ Roll shafts of Nickel Chromium Molybdenum alloyed steel, induction hardened to hardness 62-64 HRC and ground, with journals in high dynamic load roller bearings
滚轮轴是镍铬钼合金铸刚，硬度在62-64 HRC，轴颈采用高负荷滚柱轴承
§ Set of modular bending rolls heat treated to hardness 60 HRC to insure long wear resistance
模具热处理硬度达到60HRC，可以确保长时间的加工要求
§ Adjustable slip clutch fit on the upper roll. This device, essential on three driving roll machines, can slow down the rotation speed of the upper roll, compensating for the differing peripheral speeds between the inner and the outer side of the section being curved, in order to insure a smoother drive and accomplish bending radii more accurate than machines without this device.Besides, it protects the drive parts of the machine by stopping the upper roll rotation in the event of accidental overloads
液压驱动：滚轮旋转是由三个独立的带有行星式减速齿轮箱的液压系统控制，液压电机直接连接到每个轴上。液压控制系统能够保证上侧滚轮的低速旋转。
此外，在设备超负荷的情况下，通过停止上侧滚轮的旋转来保护设备的驱动部分依据压力计，通过旋钮来调节圆周速度补偿。
§ All gear journals on shafts through involute spline (DIN 5482)
所有的驱动部分密封润滑
§ Electro-mechanical drive transmission carried out with AC motor, reduction gearbox, chain and gears
机电传动进行了交流电机,减速齿轮箱、齿轮链
§ Machine frame of fabricated and machined steel plate
设备是钢板焊接结构
§ Helical reduction gearbox, oil bath lubricated
螺旋减速齿轮箱，润滑油槽
§ Hydraulic unit enclosed in the machine frame, protected by overload relief valves and driven by a dedicate AC motor
液压系统集成在设备内，具有过载阀保护，AC电机驱动
§ Check valves on hydraulic cylinders to insure constant roll position under load
液压系统的止回阀锁定加工时的滚轮位置
§ Remote controls at low voltage on a free standing console, including:
低电压的可移动控制系统包括：
§ Foot-pedals for forward/reverse roll rotation (profile feed)
脚踏板控制前进、后退（进给速度）
§ Push buttons for adjustment of bending rolls
按钮调节滚轮
§ Numerical Control unit with video and keypad
数字控制单元带有图像和按键
§ Emergency stop palm button
紧急停止按键
